Experimental Investigation of the Shrinkage-Limit and its Impact on the Physico-Mechanical Properties of Dried Natural Clay

Authors

  • Saber Chemkhi Research and Technology Centre of Energy (CRTEn), Thermal Process Laboratory, Borj-Cedria, Tunisia Author
  • Kaouther Khalfaoui Research and Technology Centre of Energy (CRTEn), Thermal Process Laboratory, Borj-Cedria, Tunisia; University of Carthage, Laboratoire de Recherche Sciences et Technologies de l'Environnement, Borj Cedria, Tunisia Author
  • Fethi Zagrouba University of Carthage, Laboratoire de Recherche Sciences et Technologies de l'Environnement, Borj Cedria, Tunisia Author

DOI:

https://doi.org/10.64229/qfnk8r92

Keywords:

Shrinkage-limit, Clay drying, Density and porosity

Abstract

This study offers an experimental analysis of the thermo-hydro-mechanical coupling of convective-dried natural clay. The significant structural changes that the material undergoes as an unsaturated, shrinking porous medium define its final quality. The main objective of this paper is to explain the coupling of mass, energy, and momentum transfers, by the so-called shrinkage-limit of the porous medium, which is a value to be determined experimentally based on the physical and mechanical properties of the material. Characterizing how important some characteristics, such as apparent density, volumetric shrinkage, and porosity, can vary with the moisture content. Furthermore, the Young's modulus evolution during the drying stages was used to quantify the mechanical stiffness. The exact identification of the shrinkage-limit is essential to this study, which acts as a crucial transition threshold. The findings demonstrate how the material transitions from a saturated shrinking state to an unsaturated rigid phase by comparing Atterberg limits with experimental drying data. The results highlighted a strong correlation between mechanical strength and the hygroscopic state, indicating that the shrinkage-limit, found at approximately 15% water content, is essential for forecasting structural stability and averting crack formation. The established correlations provide essential data for the development of predictive models for porous media undergoing high-stress convective evaporation.

References

[1]Nait-Ali B, Alzina A, Lauro N, Smith DS. Perspectives in drying of ceramics. Open Ceramics, 2024, 17, 100554. DOI: 10.1016/j.oceram.2024.100554

[2]Kashif N, Albijanic B, Xu JJ, McGrath T, Kashif Nazir M, Hitch M, et al. Investigating the drying behaviour of clay-containing slurries. Applied Clay Science, 2024, 260, 107500. DOI: 10.1016/j.clay.2024.107500

[3]Pedrotti M, Xu L, Murray I, Tarantino A. Drying-induced volumetric behaviour of clays interpreted via binary pore-scale modelling. Computers and Geotechnics, 2024, 165, 105911. DOI: 10.1016/j.compgeo.2023.105911

[4]Tan L, Yuan Y, Zhao Z, Xu Y, Yuan Y. Insights in mechanism of drying shrinkage by pore-scale modeling of heat-moisture and stress-strain distribution for high-moisture porous media. International Journal of Thermal Sciences, 2023, 188, 108226. DOI: 10.1016/j.ijthermalsci.2023.108226

[5]Khalfaoui K, Chemkhi S, Zagrouba F. Modeling and stress analysis during drying of a deformable and saturated porous medium. Drying Technology, 2013, 31(10), 1124-1137. DOI: 10.1080/07373937.2013.777736

[6]Zhang W, Chen Y, Lai Y, Shao J, Chen L, Zhao L. A micromechanics-informed poro-elasto-plastic model for saturated cement-stabilized clay. European Journal of Mechanics-A/Solids, 2026, 118, 106082. DOI: 10.1016/j.euromechsol.2026.106082

[7]Chen L, Liu L, Shao J, Zhao L. Thermo-poro-mechanical behavior of saturated silt clay: Experiments and constitutive modelling. Journal of Rock Mechanics and Geotechnical Engineering, 2025, 17(12), 8149-8160. DOI: 10.1016/j.jrmge.2024.12.020

[8]Costa VAF. Improving the thermal performance of red clay holed bricks. Energy and Buildings, 2004, 70, 352-364. DOI: 10.1016/j.enbuild.2013.11.052

[9]Liang M, Xie J, He S, Chen Y, Schlangen E, Šavija B. Autogenous deformation-induced stress evolution in cementitious materials considering viscoelastic properties: A review of experiments and models. Developments in the Built Environment, 2024, 17, 100356. DOI: 10.1016/j.dibe.2024.100356

[10]Su Y, Cai G, Li J, Shan Y, Yang R. Investigation of hydro-mechanical coupling characteristics of stress-induced anisotropic unsaturated clay. Canadian Geotechnical Journal, 2025, 62, 1-23. DOI: 10.1139/cgj-2025-0043

[11]Kayabali K, Akturk O, Fener M, Ozkeser A, Ustun AB, Dikmen O, et al. Determination of Atterberg limits using newly devised mud press machine. Journal of African Earth Sciences, 2016, 166, 127-133. DOI: 10.1016/j.jafrearsci.2016.01.005

[12]Hammouda I, Mihoubi D. Thermodynamic and mechanical characterization of kaolin clay. Polish Journal of Chemical Technology, 2014, 16(1), 28-35. DOI: 10.2478/pjct-2014-0005

[13]Nigay PM, Cutard T, Nzihou A. The impact of heat treatment on the microstructure of a clay-based ceramic and its thermal and mechanical properties. Ceramics International, 2016, 43(2), 1747-1754. DOI: 10.1016/j.ceramint.2016.10.084

[14]Zeng H, Tang CS, Cui YJ, Najdi A. Compressive stress induced by desiccation shrinkage in clayey soils. Applied Clay Science, 2025, 267, 107729. DOI: 10.1016/j.clay.2025.107729

[15]Karagiannis N, Karouglou M, Bakolas A, Krokida M, Moropoulou A. Drying kinetics of building materials capillary moisture. Construction and Building Materials, 2017, 137, 441-449. DOI: 10.1016/j.conbuildmat.2017.01.094

[16]Wang S, Yang W, Wang C, Wang M, Ma C, Zhang Z, et al. Volume change and mechanical behavior of weakly expansive soils under wetting-drying cycles with different hydraulic coupling paths. Engineering Geology, 2025, 351, 108030. DOI: 10.1016/j.enggeo.2025.108030

[17]Hobbs PRN, Jones LD, Kirkham MP, Gunn DA, Entwisle DC. Shrinkage limit test results and interpretation for clay soils. Quarterly Journal of Engineering Geology and Hydrogeology, 2019, 52(2), 220-229. DOI: 10.1144/QJEGH2018-100

[18]Hobbs PRN, Jones LD, Kirkham MP, Roberts P, Haslam EP, Gunn DA. A new apparatus for determining the shrinkage limit of clay soils. Géotechnique, 2014, 64(3), 195-203. DOI: 10.1680/geot.13.P.076

[19]Chemkhi S, Khalfaoui K, Zagrouba F. Physico-chemical and mechanical behavior of natural clay as a porous medium during convective drying. American Chemical Sciences Journal. 2015, 6(3), 126-135. DOI: 10.9734/ACSJ/2015/15746

[20]ISO 17892-12:2018. Reconnaissance et essais géotechniques__Essais de laboratoire sur les sols-partie 12: Détermination des limites de liquidité et de plasticité. Available from: https://www.iso.org/fr/standard/72017.html (accessed on January 11, 2026).

[21]Desodt C, Reiffsteck P. Chapitre 1: Identification des sols. In Géotechnique, 2nd Edition, Paris: Dunod. 2020, 1-20.

[22]Hammouda I, Jlassi K, Mihoubi D. Changes in the physicomechanical characteristics of a ceramic paste during drying. Comptes Rendus Mécanique, 2015, 343(7-8), 419-428. DOI: 10.1016/j.crme.2015.06.001

[23]Nguyen Pham PT. Étude en place et au laboratoire du comportement en petites déformations des sols argileux naturels. Ecole des Ponts ParisTech, 2008.

[24]Collard JM, Arnaud G, Fohr JP. The drying-induced deformations of a clay plate. International Journal of Heat and Mass Transfer, 1992, 35 (5), 1103-1114. DOI: 10.1016/0017-9310(92)90171-N

[25]Chemkhi S, Zagrouba F. Development of a Darcy-flow model applied to simulate the drying of shrinking media. Brazilian Journal of Chemical Engineering, 2008, 25 (3), 503-514. DOI: 10.1590/S0104-66322008000300008

[26]EI Ouahabi M. Valorisation industrielle et artisanale des argiles du Maroc. Belgium: Liège University, 2013.

[27]Chaney R, Demars KR, Sridharan A, Prakash K. Percussion and cone methods of determining liquid limits of soils-controlling mechanisms. Geotechnical Testing Journal, 2000, 23(2), 236-244. DOI: 10.1520/GTJ11048J

[28]Abu Zreig MM, Al-Akhras NM, Attom MF. Influence of heat treatment on the behavior of clayey soils. Applied Clay Sciences, 2001, 20, 129-135. DOI: 10.1016/S0169-1317(01)00066-7

[29]Augier FF, Coumans WJ, Hugget AWB, Kaasschieter EF. On the risk of cracking in clay drying. Chemical Engineering Journal, 2002, 86(1-2), 133-138. DOI: 10.1016/S1385-8947(01)00279-0

[30]Khalili K, Heydari M, Khalili MS. Drying clays bricks with variable Young’s modulus. Procedia Technology, 2014, 12, 382-387. DOI: 10.1016/j.protcy.2013.12.503

Downloads

Published

2026-08-26

Issue

Section

Articles

How to Cite

Chemkhi, S., Khalfaoui, K., & Zagrouba, F. (2026). Experimental Investigation of the Shrinkage-Limit and its Impact on the Physico-Mechanical Properties of Dried Natural Clay. Chemical Technology and Engineering Applications, 1(2), 1-13. https://doi.org/10.64229/qfnk8r92